Ignition Timing & Knock Control

Concepts

Ignition

For more information on how fuel is delivered, see our documentation page on Fueling & Injection

Ignition, Flame, and Degrees BTDC

Gasoline engines operate on the principle of fuel combustion. Typically in a direct injection system, first, fuel is directly injected into a cylinder some time before the spark is ignited. Additionally, it is compressed during the compression stroke as the piston travels upwards towards top dead center (TDC). Relative to the top dead center position, and with its timing precisely controlled by the tuner's map, the spark plug is electrically ignited by a signal sent from the ECU to start the process of combustion.

Once combustion is started ideally with the spark plug, a flame front propagates evenly throughout the cylinder at a specific speed relative to factors such as the fuel sprayed and the air-fuel ratio. Due to the flame's propagation speed and a goal of complete combustion, the ignition of the spark plug should be timed early enough in the piston's movement that the flame can fully propagate within the available time window up to the end of the exhaust stroke, helping to ensure that the air-fuel mixture is entirely combusted before the gasses are exhausted. Additionally, the timing of the flame propagation can be precisely controlled by the spark's timing to exact an idealized amount of force on the piston as it travels downwards during the power stroke, encouraging efficient energy extraction from the fuel-air mixture.

To control this ignition timing, the ECU has a series of maps that define when the ignition spark should take place relative to the top dead center position of the piston as it ends the compression stroke. Typically, and in the Subaru DI logic, this timing is measured in degrees before the top dead center position, or BTDC. In this case, the degrees in the measurement relates to the degrees of crankshaft rotation of the engine, with a 4 stroke engine (such as the FA24) taking two full revolutions (or 720 degrees) for all 4 strokes to take place. Here is a reference of BTDC values and the timing they are associated with relative to cylinder events:

Extreme values such as 90.00°, and 180.00°, negative or otherwise, are only provided as an example reference to cylinder events; these values are entirely unrealistic for engine operation, and should not be used in real-world tuning.

Degrees Before Top Dead Center (BTDC)	Relative to TDC	Event
`180.00°`	Before	End of intake stroke, beginning of compression stroke.
`90.00°`	Before	Half-way through compression stroke, piston travels upwards towards the valves.
`0.00°`	TDC	Top dead center, power stroke begins.
`-90.00°`	After	Half-way through power stroke, piston travels downwards towards the crank-shaft.
`-180.00°`	After	End of power stroke, beginning of exhaust stroke.

Detonation (or "Knock")

Detonation and Pre-detonation

In the ideal scenario, the ignition of the air-fuel mixture in a cylinder will result in a single, evenly propagating flame front that expands outward from the spark plug at a predictable and controlled rate of expansion. This controlled expansion of the flame front results in a linear, even pressure across the cylinder walls and the piston's surface. However, it is unfortunately possible for the air-fuel mixture to spontaneously ignite in various conditions, causing one or more flame fronts to propagate throughout the cylinder's volume in an uncontrolled manner.

This spontaneous ignition of the air-fuel mixture is referred to as detonation due to the (sometimes audible) sound that is produced by multiple flame fronts colliding with each-other and creating extremely high pressure spikes inside the cylinder. Due to this sound, detonation is sometimes referred to as knock; not to be confused with rod knock, which is an entirely different phenomenon. These collisions can directly cause damage to the cylinder walls, valves, head surface, and piston surface.

Pre-detonation is similar to detonation, but occurs before the spark ignites the air-fuel mixture, as opposed to detonation which occurs at some point after the spark ignites the air-fuel mixture.

In either case, the unpredictable pressures generated by any form of detonation can exact chaotic forces on the piston surface, suddenly forcing its connecting rod into the crankshaft, possibly damaging the rod bearing. This is especially true for pre-detonation, where the spontaneous ignition can occur as the piston is completing its upwards travel to complete the compression stroke, violently interrupting the piston's only available direction of travel in possibly its most critically pressurized moment.

Detonation and pre-detonation can be caused by several factors, often compounding together simultaneously:

Faulty spark plugs or fuel injectors.
An air-fuel mixture that is too lean or too rich for proper combustion with cylinder conditions.
Low fuel octane, the measurable capability of a fuel to resist detonation. Fuels such as 93 or E85 have a higher octane rating than perhaps 87 or 91, but it is possible for fuel to lose octane after sitting for a long period of time. Fuel octane can be affected by any contaminants such as oil or coolant mixing with the air and fuel in a cylinder.
An ignition timing value that is too advanced (earlier in time).
A compression ratio incompatible with cylinder conditions and the commanded ignition timing. Compression ratios can be increased by carbon deposits (buildup) inside a cylinder.
Excessive temperatures inside the cylinder, including air temperature and hot spots within the cylinder surfaces. Carbon deposits can also be sources of these hot spots.

Subaru Knock Control

Introduction

Mitigation

As detonation and pre-detonation can be dangerous events, entirely eliminating all forms of detonation (or "knock") is an extremely important goal of any gasoline ignition strategy. By reducing (also referred to as retarding or pulling) the base ignition timing later in the engine cycle or by modifying the air-fuel ratio, it is possible for an ECU to significantly mitigate detonation events. While pre-detonation can be mitigated this way as well, it is likely that additional factors are involved if it is occurring.

Unfortunately, delaying the ignition timing implies that torque would likely be lost due to the decreased mechanical advantage imparted by the piston on the crankshaft from the flame front's delayed propagation. However, this is a valuable trade-off, as an engine won't be making any torque (or, at best, significantly less) if severe detonation event(s) occur and cause damage to cylinders or other engine components.

Why Pull Timing?

It is important to note that if we are reducing (pulling back) ignition timing, we are effectively delaying (or retarding) the spark event's occurrence in time relative to the engine's cycle. This has effects that help mitigate detonation, with one primary advantage being that we are allowing for more time for entropy to do its job and to enabling the air and fuel to mix within the volume of the cylinder.

Additionally, the environment within the cylinder becomes less favorable for detonation as the piston moves past its top dead center and travels downward in the power stroke. This downward motion has the important effect of increasing the cylinder volume, which correspondingly decreases the air-fuel mixture's density as the valves remain during the power stroke. This reduction of density reduces the cylinder's pressure and temperature, both highly advantageous effects to mitigate detonation.

Sensors

Knock Sensors

On the Subaru FA platform, two piezoelectric sensors called knock sensors are bolted directly onto the factory short block. With both positioned in the rear of the crankcase, nearest the bell housing,

Mitigation Stategies

Feedback Knock (FBK)

Fine Knock Learning (FKL)

Dynamic Advance Multiplier (DAM)